ARCTIC P14 Pro Reverse A-RGB 3-Pack 140mm PWM Fan - Black, FDB
ARCTIC
ARCTIC P14 Pro Reverse A-RGB 3-Pack 140mm PWM Fan - Black, FDB
Three ARCTIC P14 Pro Reverse A-RGB fans in black — part ACFAN00327A. These are 140 mm PWM fans with the blades running the other way, so the lit, finished face points into the case while the air is pulled from behind. Twelve addressable LEDs per fan, 400–2650 rpm with a true 0 rpm mode, and a six-year warranty.
Why this product
Reverse blades — the good side faces you
On a standard fan the attractive side is the intake side, which ends up hidden. Reverse blades flip the airflow so the finished, lit face points into the case while the fan still draws air from behind it.
12 addressable LEDs per fan
Each fan carries 12 A-RGB LEDs on a 3-pin 5 V addressable connector, with a pass-through socket so the lighting chains fan to fan.
400–2650 rpm with 0 rpm mode
PWM controlled across a wide range, and ARCTIC stops the fan completely below 5% PWM — genuinely silent at idle rather than just quiet.
98 CFM and 5.1 mmH₂O
Strong figures for a 140 mm fan, with the static pressure to work on radiators and restrictive mesh rather than only in open air.
PST daisy-chaining
A second 4-pin socket on each fan lets all three chain to a single motherboard header, sharing one PWM signal.
Six-year warranty
ARCTIC covers these for six years, on a fluid dynamic bearing.
- Part numberACFAN00327A
- Pack quantity3 fans
- Size140 × 140 × 30 mm
- ColourBlack
- Speed400–2650 rpm, PWM, 0 rpm below 5%
- Airflow98 CFM
- Static pressure5.1 mmH₂O
- Lighting12 A-RGB LEDs per fan
- SKUARC-3527
- EAN4895265000775
- 140 mm mounting pattern. Note the frame is 30 mm deep rather than the usual 25 or 27 mm — check clearance in tight builds.
- 4-pin PWM fan plug plus a 4-pin socket for PST daisy-chaining, with a 400 mm cable and an 80 mm daisy-chain lead.
- 3-pin 5 V addressable RGB plug plus a 3-pin socket, so the lighting chains between fans and into a standard A-RGB header.
- 12 V DC with a 4 V start-up voltage and 0.4 A draw, plus 0.40 A at 5 V for the lighting.
- Three fans and mounting screws are supplied. ARCTIC does not list a manual speed controller or a hub with this pack.
- ARCTIC publishes no noise rating for this model.
- Rated for an ambient operating range of 0–40 °C.
Best for
- Glass-panel builds where the fans are on display and you want the finished face pointing outward.
- Rear, top and bottom mounts where a standard fan would show its back to the window.
- Radiators and restrictive mesh, on 5.1 mmH₂O of static pressure.
- Silent idling, since the fans stop entirely below 5% PWM.
- Tidy cabling — both the PWM and the A-RGB chain fan to fan.
Trade-offs
- Tight clearances: ARCTIC specifies a 30 mm frame depth, deeper than a standard 25 mm fan. Some retailers list 27 mm; ARCTIC's own figure is 30 mm.
- Conventional airflow layouts: these are reverse-blade fans. In a normal front-intake position a standard fan is the right choice.
- Buyers who need a quoted noise level: ARCTIC publishes no dB(A) or Sone figure for this model.
- Setups needing a controller in the box: no manual speed controller or hub is listed with this pack.
Three ARCTIC P14 Pro Reverse A-RGB fans in black — part ACFAN00327A.
The reverse blade is the whole point. On an ordinary fan the attractive, lit face is the intake side, which means that in a rear, top or bottom mount the side on show through the glass is the bare motor hub and struts. These run the other way: the finished face points into the case while the fan draws its air from behind, so the build looks right from the window without compromising the airflow direction.
Each fan carries 12 addressable RGB LEDs on a 3-pin 5 V connector with a pass-through socket, and runs on PWM from 400 to 2650 rpm. ARCTIC stops the blades entirely below 5% PWM, so an idle machine is silent rather than merely quiet. Airflow is 98 CFM at 5.1 mmH₂O of static pressure, on a fluid dynamic bearing.
Both sets of cables chain: a second 4-pin socket carries the PWM signal from fan to fan so all three run from one header, and the A-RGB connector does the same for the lighting. Three fans and mounting screws are supplied, with a six-year warranty.
Two things to check before buying. The frame is 30 mm deep to ARCTIC's own specification, not the usual 25 mm, so clearance matters in tight builds. And ARCTIC publishes no noise rating for this model — we would rather say that than quote a figure from elsewhere.
General
| Brand | ARCTIC |
|---|---|
| Model | P14 Pro Reverse A-RGB |
| Part number | ACFAN00327A |
| EAN | 4895265000775 |
| Colour | Black |
| Pack quantity | 3 fans |
| Blade direction | Reverse (5 blades) |
Performance
| Fan speed | 400–2650 rpm, PWM controlled |
|---|---|
| 0 rpm mode | Yes — stops below 5% PWM |
| Airflow | 98 CFM / 166.5 m³/h |
| Static pressure | 5.1 mmH₂O |
| Bearing | Fluid dynamic bearing |
| Noise | Not published by ARCTIC |
Lighting
| LEDs | 12 addressable per fan |
|---|---|
| Connector | 3-pin A-RGB plug and 3-pin socket |
| Lighting power | 0.40 A at 5 V DC |
Electrical & Connection
| Fan connector | 4-pin PWM plug and 4-pin socket (PST daisy-chain) |
|---|---|
| Voltage | 12 V DC (typical) |
| Start-up voltage | 4 V |
| Current | 0.4 A per fan |
| Cable length | 400 mm, plus 80 mm daisy-chain lead |
Physical
| Fan dimensions | 140 × 140 × 30 mm |
|---|---|
| Weight | 253 g per fan |
| In the box | 3 fans, mounting screws |
| Operating ambient | 0–40 °C |
| Warranty | 6 years |
Shipping
All our products are shipped from the United Kingdom within 24 to 48 hours of purchase. See our Shipping and Returns page for full details.
Returns
- Tech Syndicate offers a full money-back guarantee on all purchases made in our store. If you are not satisfied with your purchase, we will provide a full refund, no questions asked.
- Refunds are available within 45 days of delivery.
- After the 45-day period you are no longer eligible for a refund, so we encourage you to try the product within the first few weeks to make sure it fits your needs.